Skip to main content

CurryKitten

  • About
  • Support Me
  • YouTube
  • CurryKitten FPV Sim Mobile Edition
  • Facebook
  • Contact Me

Tag: plane

Skyhook Discovery 2.6 build – Part 4 (Camera mount, securing the tail, and finishing off)

31st August 201831st August 2018 CurryKitten Leave a comment

In this final build part of the Skyhook, there wasn’t actually much left to do.  The electronics were mostly in place, but there were just some annoying pieces to tick off the list. First up was the camera mount.  To start with, we had a slightly confusing set of parts along with my camera – […]

Read More

Skyhook Discovery 2.6 Build – Part 3 (Installing electronics, finishing the wings)

23rd June 201830th August 2018 CurryKitten Leave a comment

After installing (most) of the servos in the last part of this build, I seemed to be caught up in a circular dependency situation where everything I wanted to start installing seemed to depend upon another already being present.  I had the flap servos, receiver and VTX to install but how could I do this […]

Read More

The History of FPV

10th December 201710th December 2017 CurryKitten 9 Comments

I’ve done a bit of work for RC magazines over the past few years, and one of the most interesting bits to write was a piece I was asked to do for “RC Flight Camera Action” magazine on the history of FPV.  I’ve been FPVing since 2012, and have been around long enough to see […]

Read More

Skyhook Discovery 2.6 Build – Part 2 (Installing the servos)

24th July 201730th August 2018 CurryKitten 2 Comments

Next part of the Skyhook build was the servo installation.  On your regular foamy style plane, it’s a job that takes a few minutes – often you can just pop the servos straight into a pre-cut hole, maybe you’ll need to trim a little extra out.  With the Skyhook, there’s a little more to do. […]

Read More

The MiniRaceWing build and FPV maiden

14th July 201714th July 2017 CurryKitten Leave a comment

I’ve been championing the MiniRaceWing for a while now.  For those not familiar with the background, it started as a Kickstarter project for a new type of wing.  The basic premise was to use a mini-quad like carbon fiber centre section with wings that would detach in a crash to avoid any damage.  I made a […]

Read More

Skyhook Discovery 2.6 Build – Part 1 (Mounting the motor)

29th June 201730th August 2018 CurryKitten 2 Comments

I’d touched on the Skyhook Discovery back in a previous post, and if you’d watched the accompanying video, then you’ll know that I was nervous about building it.  Basically, I didn’t want to screw the build up, and destory what is a lovely looking model.  I guess the build intimidates me a little because it’s […]

Read More

Getting iNav ready for the SkyHook Discovery 2.6 – enter the cardboard V-Tail

20th June 201730th August 2018 CurryKitten 8 Comments

Last month I got the biggest plane I’d ever held in my hands for a review.  This is the Skyhook Discovery 2.6.  It’s a really quite stunning 2.6m motor-glider that’s made of balsa and composite and has been careful thought out for flying FPV.  It is huge, but thankfully it all breaks back down a […]

Read More

Search

Want to be notified when new content is published ?

Recent Posts

  • Open.HD a new Setup and Config guide
  • Setting up a GPS with Betaflight
  • Using SPI receivers with an ACCESS/ACCST LBT/EU radio
  • Using the DShot Beeper in Betaflight – a quick and easy guide
  • GepRC MX3 Sparrow review (from Drone May 2018)

Categories

  • Article (10)
  • Builds (12)
  • Magazine (8)
  • Reviews (6)
  • Setup (6)
  • Tutorial (11)
  • Uncategorised (3)

Gearbest Get ready for Gearbest 4th Anniversary promotion

  • About
  • Support Me
  • YouTube
  • CurryKitten FPV Sim Mobile Edition
  • Facebook
  • Contact Me
Theme by Colorlib Powered by WordPress