Skip to main content

CurryKitten

  • About
  • Support Me
  • YouTube
  • CurryKitten FPV Sim Mobile Edition
  • Facebook
  • Contact Me

Tag: build

Open.HD a new Setup and Config guide

28th July 202128th July 2021 CurryKitten Leave a comment

About a year ago I made 3 videos about Open.HD and they are still sat there on YouTube if you’d like to take a look. in the first video, I talk about what Open.HD is and what sort of equipment we’ll need to get the system set up. In the next video, I connected everything […]

Read More

Skyhook Discovery 2.6 build – Part 4 (Camera mount, securing the tail, and finishing off)

31st August 201831st August 2018 CurryKitten Leave a comment

In this final build part of the Skyhook, there wasn’t actually much left to do.  The electronics were mostly in place, but there were just some annoying pieces to tick off the list. First up was the camera mount.  To start with, we had a slightly confusing set of parts along with my camera – […]

Read More

Skyhook Discovery 2.6 Build – Part 3 (Installing electronics, finishing the wings)

23rd June 201830th August 2018 CurryKitten Leave a comment

After installing (most) of the servos in the last part of this build, I seemed to be caught up in a circular dependency situation where everything I wanted to start installing seemed to depend upon another already being present.  I had the flap servos, receiver and VTX to install but how could I do this […]

Read More

The History of FPV

10th December 201710th December 2017 CurryKitten 9 Comments

I’ve done a bit of work for RC magazines over the past few years, and one of the most interesting bits to write was a piece I was asked to do for “RC Flight Camera Action” magazine on the history of FPV.  I’ve been FPVing since 2012, and have been around long enough to see […]

Read More

Adding the RunCam Micro Swift camera to a Micro quad

21st September 201728th September 2017 CurryKitten 4 Comments

If there’s one thing the current crop of micro quads have in common (and for the purposes of discussion, I’ll class micro quads as up to 130mm motor-to-motor) it’s the quality of the camera in the all-in-one VTX/Camera combos. That’s not to say they are awful – in fact that fact we get a tiny camera […]

Read More

Moving from the Aurora 100 to a Firer 110 Frame

2nd August 20172nd August 2017 CurryKitten Leave a comment

The Aurora 100 has become my favorite quad, after getting one sort of out of the blue from Banggood to review…. and that’s not just favorite micro quad, I mean quad of all dimensions.  I was out a few weeks ago flying with my friend Neil (he also had an Aurora) when disaster finally struck.  We […]

Read More

Skyhook Discovery 2.6 Build – Part 2 (Installing the servos)

24th July 201730th August 2018 CurryKitten 2 Comments

Next part of the Skyhook build was the servo installation.  On your regular foamy style plane, it’s a job that takes a few minutes – often you can just pop the servos straight into a pre-cut hole, maybe you’ll need to trim a little extra out.  With the Skyhook, there’s a little more to do. […]

Read More

The MiniRaceWing build and FPV maiden

14th July 201714th July 2017 CurryKitten Leave a comment

I’ve been championing the MiniRaceWing for a while now.  For those not familiar with the background, it started as a Kickstarter project for a new type of wing.  The basic premise was to use a mini-quad like carbon fiber centre section with wings that would detach in a crash to avoid any damage.  I made a […]

Read More

Skyhook Discovery 2.6 Build – Part 1 (Mounting the motor)

29th June 201730th August 2018 CurryKitten 2 Comments

I’d touched on the Skyhook Discovery back in a previous post, and if you’d watched the accompanying video, then you’ll know that I was nervous about building it.  Basically, I didn’t want to screw the build up, and destory what is a lovely looking model.  I guess the build intimidates me a little because it’s […]

Read More

Martian III Quad build – Part 2

23rd June 201723rd June 2017 CurryKitten 4 Comments

In the first part of the build, we discussed the parts I gathered to build the Martian III, so let’s actually get on and put it together now.  First off, this means disassembling most of the frame down again – just leaving the legs and the base plate – I’ve done this so I can […]

Read More

Posts pagination

1 2 Older posts

Search

Want to be notified when new content is published ?

Recent Posts

  • Open.HD a new Setup and Config guide
  • Setting up a GPS with Betaflight
  • Using SPI receivers with an ACCESS/ACCST LBT/EU radio
  • Using the DShot Beeper in Betaflight – a quick and easy guide
  • GepRC MX3 Sparrow review (from Drone May 2018)

Categories

  • Article (10)
  • Builds (12)
  • Magazine (8)
  • Reviews (6)
  • Setup (6)
  • Tutorial (11)
  • Uncategorised (3)

Gearbest Get ready for Gearbest 4th Anniversary promotion

  • About
  • Support Me
  • YouTube
  • CurryKitten FPV Sim Mobile Edition
  • Facebook
  • Contact Me
Theme by Colorlib Powered by WordPress